1ST- PRINTING -NV
SEGA ENTERPRISES,LTD.
SfU
QfmtJMmj
UPRIGHT TYPE
OWNER’S MANUAL
MANUAL NO. 420-5305-02
TABLE OF CONTENTS
INTRODUCTION OF THE OWNER’S MANUAL 2
1. HANDLING PRECAUTIONS 2
2. PREVENTION OF COUNTERFEITING AND CONVERSION 3
3. PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION 4
4. NAME OF PARTS 5
5. SERVICING THE HANDLE UNIT AND WINDOW MASK 6
6. DISASSEMBLING AND ADJUSTING THE HANDLE UNIT 7-8
7. DISASSEMBLING AND ADJUSTING THE ACCELERATOR AND BRAKE 9
8. ADJUSTING THE ACCELERATOR/BRAKE POTENTIOMETER 10
9. ADJUSTMENT OF THE SERVICE SWITCH 11
10. INSTRUCTION OF BOARD AND CONNECTORS 12
11. DIP SWITCH SETTING 13
12. EPROM/ROM LOCATIONS 14-15
13. SELF -TESTING 10-22
14. PARTS LIST 23-39
15. WIRING DIAGRAM 40
UPRIGHT TYPE
SPECIFICATIONS
INSTALLATION SPACE : 630 mm ( 25 in.) Wx 970 mm ( 38 in.) D
HEIGHT : 1815 mm(71.5in.)
POWER '■ 250 W
C. R. T. : 20"
WEIGHT : 110 kg (242.5 lbs)
NOTE
o Descriptions herein contained may be subject to improvement
changes without notice.
- 1 -
INTRODUCTION OF THE OWNER’S MANUAL
SEGA ENTERPRISES, LTD., supported by its high electronic
technology of LSIs, microprocessors, etc. and a wealth of
experience, has for more than 30 years been supplying various
innovative and popular game machines to the world market. This
OWNER 1 S manual is intended to provide detailed comments
together with all the necessary information covering the opera-
tion in general of electronic assemblies, electromechanicals,
servicing control, spare parts, etc. as regards the OUT RUN,
a new SEGA product. The manual is intended for those who have
knowledge of electricity and technical expertise especially in
ICs, CRTs, microprocessors, etc. Carefully read so as to acquire
sufficient knowledge before working on the machine. Should there
be a malfunction, non-technical personnel should under no
circumstance touch the interior system.
1. HANDLING PRECAUTIONS
When installing or inspecting, be very careful of the
following points and pay attention to ensure that the player
can enjoy the game safely.
o Be sure to turn the power off before working on the machine,
o To insert or pull out the plug quickly is dangerous,
o It is necessary to make sure that the power cord or the
grounding wire is not exposed on the road, etc. in a manner
so as to be dangerous. Make sure that grounding connections
are made safely at the position where so specified,
o Do not use any fuse that does not meet the specified rating,
o Make complete connections for the IC board and other
connecters. Insufficient insertion is very dangerous.
Also, for the IC board circuit inspections, only the logic
tone is allowed. The use of a tester is not permitted, so be
careful in this regard. After confirming that there are no
irregularities, turn the power ON.
-2
2. PREVENTION OF COUNTERFEITING AND CONVERSION
LABELLING
To prevent counterfeits and conversions, the following
labels are put on all the SEGA products. When handling such
goods, be sure to confirm the labels. They are used to
prevent illegal acts such as the unauthorized copying of the
products and the printed circuit boards thereof or carrying
on business by manufacturing similar merchandise or by
converting, selling or using such products or printed
circuit boards.
ORIGINAL SEAL
The following seal is put on
the machines manufactured by
SEGA.
LICENSE SEAL
The following seal is put on the
kits, such as the printed
circuit boards, of SEGA
products .
i [t'J vi~ Ml ,
4 [original seal!
HIS PRODUCT is DE SI<3NE 0
AND MANUFACTURER BY
S E QA E NTf«P R is F..S l T D
ORIGINAL JJ
OUT RUN
NO
SfGA ENTERPRISES l
■‘"4'* -"T* •
1 LjCfNSt SEAL
T.HiS P#CK)UCT.4S
MAISJUFAI* TU R f D UNDER
I t he ncFNS.E of
S fee. A ENTt fi P RlS f S LTD
UCfNSl »
OUT RUN
NO.
. S E G AT E NTFRPRISES
COPYRIGHT NOTICE
This SEGA product has the copyright notice as follows:
© SEGA 1986
This signifies that this work was disclosed in 1986 and is the
property of SEGA ENTERPRISES, LTD.
- 3 -
3. PRECAUTIONS CONCERNING THE PLACE OF INSTALLATION
The OUT RUN is an indoor game machine. Absolutely do
not install it outside. Even indoors, avoid installing in
places mentioned below so as to ensure proper usage:
o Places subject to rain or water leakage, or condensation due
to humidity.
o In the proximity of an indoor swimming pool and/or shower.
o Places subject to direct sunlight.
o Places subject to heat sources from heating units, etc., or
hot air.
o Vicinity of highly inf lammabl e/ volatile chemicals or
hazardous matter.
o Sloped surfaces.
o Vicinity of anti-disaster facilities such us fire exits and
fire extinguishers.
o Places subject to any type of violent impact.
o Dusty places.
- 4 -
4. NAME OF PARTS
ASSY ACCEL & BRAKE V/R
KR-12002
DESIGN PLATE OUT RUN
423-0031
WINDOW MASK
KR-1068
ASSY SHIFT LEVER
KR-13001
20" MONITOR
200-5090
PLAY INST SH
422-0168
COIN ENTRY
ASSY CONTROL PANEL
KR-11001
START BUTTON
TOOLS
(TAMPERPROOF WRENCH) (TAMPERPROOF WRENCH)
M4 540-0006-01
M 5 540-0007-01
M6 540-0015-01
M8 540- 0009-01
M4 540-0018
M5 540-0017
5. SERVICING THE HANDLE UNIT AND WINDOW MASK
TAMPERPROOF SCREW
M5xl6
ASSY CONTROL PANEL
KR-11001
CABINET
FRAME UPPER
KR-1065
WINDOW MASK
KR-1068
TAMPERPROOF
«£\ SCREW M8X30
bsU J
DESIGN PLATE OUT RUN
423-0031
WINDOW GLASS
HN-1039X
TAMPERPROOF
SCREW M4xl6
® The HANDLE UNIT can be opened towards you by taking off the 3
TAMPERPROOF screws.
(2) To remove the WINDOW MASK from the cabinet, take off
the TAMPERPROOF screws (M4x8) inside the WINDOW MASK.
® Next open it towards you.
This allows for the clearing of the monitor screen (CRT
surfaces) .
- 6 -
6. DISASSEMBLING AND ADJUSTING THE HANDLE UNIT
To open the dashboard, take off the 2 M8 TAMPERPROOF
screws .
After doing this, spring replacements and steering
adjustments can be made.
TAMPERPROOF SCREW M8
(I) Release the 2 adjusting screws of the potentiometer
bracket and perform the necessary adjustments by changing its
gear position, making sure that the variable is within the
allowable extent as shown below, and then retighten the
adjusting screw.
POTENTIOMETER
ADJUSTMENT SCREW
POTENTIOMETER BRACKET
Minimum ( 33 )
Maximum (CB)
Allowable adjustment range
7. DISASSEMBLING AND ADJUSTING THE ACCELERATOR
AND BRAKE
To remove the accelerator/brake unit, take off the 7 M5
TAMPERPROOF SCREWS.
TAMPERPROOF
SCREW (M5X16)
ACCELERATOR/BRAKE
UNIT
ACCELERATOR
PEDAL
BRAKE PEDAL
-9
8. ADJUSTING THE ACCELERATOR/BRAKE POTENTIOMETER
CD Display the SELF-TESTING MODE screen shown on page 16 .
( 2 ) Release the adjustment screws, move the bracket, and make
adjustments so that the variable becomes 20H when the
accelerator/brake is released and returns to its original
position .
: 3 ) Even after the above procedure has been followed, if the
variable is not within the allowable range, then slightly turn
the gear to make an adjustment.
ADJUSTMENT SCREW A
BRAKE
POTENTIOMETER
ACCELERATOR PEDAL
BRAKE PEDAL
BRAKE BRACKET
SCREW B
E GEAR
ACCELERATOR BRACKET
ACCELERATOR
Minimum
( 20 )
Brake
( 20 )
Standard
o
Maximum (fully open)
(D5)
1 CH 1 DH 1 EH 1 FH 20H 21H 22H 23H 24H
Allowable adjustment range
(CB)
- 10 -
9. ADJUSTMENT OF THE SERVICE SWITCH
The layout as shown below can be viewed by opening the coin
chute door.
CASHBOX
COIN CHUTE DOOR
© DEMAGNETIZING
SWITCH
© SERVICE SWITCH
© TEST SWITCH
POTENTIOMETER KNOB
OPERATING INSTRUCTIONS
©DEMAGNETIZING SWITCH Used for removing the on-screen color
unevenness.
©SERVICE SWITCH Used for the purpose of servicing and
increasing the credits without
registering on the meter (this allows
you to check the game).
©TEST SWITCH For operating this switch, see
SELF-TESTING.
0 POTENTIOMETER ADJUSTMENT
- 11 -
10. INSTRUCTION OF BOARD AND CONNECTORS
20P
POTENTIOMETER GROUP
- 12 -
ONE
TIME KOM
GAME
BD
834-6065-01
834-6065-02
CPU
BD
837-6063-01
837-6063-02
Road
IC
11
OPR- 10185
5k
Character
IC
47
OPR- 10186
IC
76
EPR- 10327
EPR— 10327A
Sub
IC
75
EPR- 10328
EPR- 10328A
Program
IC
58
EPR- 10329
EPR — 10329A
IC
57
EPR -10330
EPR— 10330A
IC
133
EPR- 10331
EPR- 10380 A
Main
IC
132
EPR- 10332
EPR- 10381 A
Program
IC
118
EPR — 10333
EPR- 10382 A
IC
117
EPR- 10334
EPR- 10383 A
P
IC
88
EPR — 10187
IC
71
OPR— 10188
IC
70
OPR- 10189
Sound
Data
IC
69
OPR -10190
*
IC
68
OPR — 10191
IC
67
OPR— 10192
1C
66
OPR — 10193
VIDEO BD
837-6064-01
837-6064-01
IC
9
OPR— 10194
1C
13
OPR- 10195
1C
17
OPR — 10196
1C
21
OPR— 10197
1C
25
OPR— 10198
1C
29
OPR— 10199
IC
33
OPR- 10200
IC
37
OPR — 10201
IC
10
OPR -10203
IC
14
OPR -10204
1C
18
OPR -10205
IC
22
OPR -10206
IC
26
OPR -10207
IC
30
OPR- 10208
IC
34
OPR -10209
IC
38
OPR -102 10
IC
11
OPR — 10212
5k
IC
15
OPR -102 13
Object
IC
19
OPR — 10214
IC
23
OPR — 10215
IC
27
OPR — 10216
IC
31
OPR — 10217
IC
35
OPR— 10218
IC
39
OPR— 10219
IC
12
OPR— 10221
IC
16
OPR — 10222
IC
20
OPR— 10223
IC
24
OPR— 10224
IC
28
OPR -10225
IC
32
OPR — 10226
1C
36
OPR- 10227
IC
40
OPR — 10228
IC
104
OPR — 10230
IC
103
OPR — 10231
Scroll
IC
102
OPR -10232
IC
101
OPR -10266
1C
100
OPR -10267
IC
99
OPR -10268
S MASK ROM |
GAME BD
834-6065-03
834-6065-04
r
CPU BD
837-6063-01
837-6063-02
Road
IC
11
OPR- 10185
*
Character
1C
47
OPR — 10186
r ■
'
IC
76
EPR- 10327
p;PR-10327A
Sub
IC
75
EPR- 10328
EPR— 10328A
Program
IC
58
EPR -10329
EPR— 10329A
|
IC
57
EPR- 10330
EPR- 10330A
IC
133
EPR- 10331 1
EPR- 10380 A
Main
IC
132
EPR — 10332
EPR — 10381 A
Program
IC
118
EPR- 10333
EPH - 10382 A
1C
117
EPR — 10334
EPH- 10383 A
P
IC
88
EPR- 10187
1C
71
OPR — 10188
Data
IC
70
OPR — 10189
*
TC
69
OPR— 10190
IC
68
OPR — 10191
IC
67
OPR- 10192
IC
66
OPR — 10193
VIDEO
> BD
837-6064-02
837-6064-02
[IC
9
MPR-10371
10
13
M PR -10372
IC
10
MPR-10373
Object
IC
14
MPR-10374
IC
11
MPR-10375
1C
15
MPR-10376
IC
12
MPR-10377
5k
IC
16
MPR-10378
1C
104
OPR -10230
IC
103
OPR — 10231
Scroll
IC
102
OPR — 10232
IC
101
OPR- 10266
IC
100
OPR -10267
IC
99
OPR- 10268
* SAME AS THE PREVIOUS COLUMN.
P : PROGRAM
- 15 -
13. SELF -TESTING
The main purposes of these tests are to check the operations of
the game boards, to find the defects if any, to adjust the
monitor colors properly, and to make sure the sounds are
produced satisfactorily. It is also performed to indicate the
assignments of the dip switches, check bookkeeping functions,
etc .
KIND OF TESTS
1) Memory Test:
2 ) Input Test :
3) Output Test:
4) Motor Test:
5) Sound Test:
6) CRT Test:
7) Dip Switch
Assignment :
8) Bookkeeping:
9 ) Backup RAM
To check the EPROM programs and the map area
of the RAMs.
To test the operation of the coin switch,
shift lever, handle/accelerator, brake, start
switch, service switch, etc.
To test the operation of the lamps.
Tests in this mode are not applicable
for the upright type.
To check the quality of the sounds produced by
the PCB and the video disc, and to adjust the
balance of the speakers.
To check if the colors on the monitor are
displayed correctly.
To indicate each dip switch assignment.
To indicate information data on average score,
average play time, etc.
When the power is turned off, a backup
battery system automatically takes over, thus
allowing the continuous storage of all
bookkeeping dat'a. Using this item will
enable you to clear said data.
10 ) EXIT
See page 22.
16 -
1. TEST OPERATION
(1) Push the test switch and Fig. 1 will be shown on the
screen .
(2) Select CONTINUE or INDIVIDUAL by using the START button.
DIAGNOSTIC
-A> [CONTINUE]
MEMORY TEST
INPUT TEST
OUTPUT TEST
MOTOR TEST
SOUND TEST
CRT TEST
DIP SW. ASSIGN
BOOKKEEPING
BACKUP RAM CLEAR
EXIT
SELECT BY STEERING
PUSH TEST BUTTON/
(3) Move the steering to bring the
arrow to the desired position.
FIG. 1
[CONTINUE] :
o Bring the arrow sign to CONTINUE
first, and move it to one of the
tests to start. Push the TEST
button, and the tests will be
performed in order, one by one,
starting from the test where the arrow
was originally set to EXIT.
o If the START button is pushed when the
arrow is at CONTINUE, it will change
to INDIVIDUAL. Pushing it again
returns it to CONTINUE.
[INDIVIDUAL]:
o If the arrow is at INDIVIDUAL first
and brought to a certain test which
you want to conduct, only that test is
performed by pushing the TEST button.
- 17 -
(4) When each test is finished, push the TEST button. In the
case of CONTINUE, push the TEST button, and it will
automatically go into the following test. If the TEST
button is pushed in the case of INDIVIDUAL, FIG. 1 is
shown. If you want to end the test mode at this time,
bring the arrow to EXIT and push the TEST button again,
and it will return to the ADVERTISEMENT mode.
2. TEST ITEMS
(1) Memory Test:
Indication of "GOOD" following the IC No. means the IC is
all right. Push the TEST button to proceed to the
following test item:
(2) Input Test
<
HANDLE
7CH 7DH 7EH 7FH '.8011 81H 82H 83H 84H
1CH 1DH 1EH 1FH ^OH] 21H 22H 23H 24H
Standard value
Standard value
- 18 -
o Operate the dip switches. When "ON" is indicated at the right
side of the corresponding item on the screen, it is OK.
o If the data value increases when pressure is applied to the
accelerator's or brake's pedal, it tests out satisfactorily.
o When the tests are ended, push the TEST button.
(3) Output Test
If the start LAMP lights up, it is functioning properly.
Push the TEST button when the testing has been completed.
- 19 -
( 4 ) Sound test
DIAGNOSTIC
SOUND TEST
1. COIN IN
10.
VOICE 1
2. CHECK POINT
11.
VOICE 2
3. Signal i
12.
VOICE 3
4. SIGNAL 2
13.
VOICE 4
5. SLIP
14.
WAVE
6. SAFETY ZONE
15.
CHEERS
7. CRASH 1
16.
MUSIC 1
8. CRASH 2
17.
MUSIC 2
9. REBOUND
18.
MUSIC 3
SELECT BY STEERING
PUSH START BUTTON/
When the test has been completed, push the TEST button.
( 5) C.R.T. Test
When the test has been completed, push the TEST button.
- 20 -
(6) DIP SWITCH ASSIGNMENTS
DIAGNOSTIC'
DIP SWITCH ASSIGNMENT
1 2 3 4 5 6 7 8
DIP SW. A OFF OFF OFF OFF OFF OFF OFF OFF
DIP SW. B OFF OFF OFF OFF OFF OFF OFF OFF
A
B
1234 COIN SW#1 1 COIN
5678 COIN SW #2 1 COIN
12 TYPE
3 ADVERTISE SOUND
56 TIME ADJ.
78 NUMBER OF ENEMY
1 CREDIT
1 CREDIT
-Present Setting of the
Dip Switches.
Coin Switch Setting.
COCKPIT ^ |
r OFF
OFF
MOVING TYPF
/ON
1 ON
OFF
UP COCKPIT
1 OFF
ON
MINI UP
NORMAL x
ON
ON
NOT US HD
NORMAL, \
f
i
7) Bookkeeping
Adjustment of the game time
The appearance frequency of the other car
/f ON Sound is emitted at the time
Of GAME OVER.
OFF No sound is emitted at the time
of GAME OVER.
DIAGNOSTIC
BOOKKEEPING
COIN CHUTE #L 0
COIN CHUTE #2 0
COIN CREDIT 0
SERVICE CREDIT 0
TOTAL CREDIT 0
TOTAL TIME []H □ M □ S
PUSH START BUTTON'
Usage frequency of coin chute 1
Usage frequency of coin chute 2
Number of coin credits
Usage frequency of service switch
Number of credits
Operating time ( hour -minute-second )
* Only the data that falls within the range of up to 999H 59M
59S can be memorized.
The above screen indication is for testing.
When the tests are finished, push the START button and the
following will be shown:
-21
DIAGNOSTIC'
BOOKKEEPING
NUMBER OF GAME 203
AVE. SCORE 7230
TOP-SCORE 9320
LOW -SCORE 4230
* * GAME TIME * *
TOTAL Dh Dm as
AVERAGE □» DM QS
LONGEST □» DM DS
PUSli START BUTTON 1
Every time the START button is pressed, the bookkeeping test
display is repeated.
o When the tests are ended, push the TEST button.
(8) Backup RAM Clear:
To clear the data, bring the arrow to "YES" and push the
TEST button.
When the test is linished, push the TEST button to end the
test (in the case of "INDIVIDUAL," however, the test mode
returns to Fig. 1 first).
( 9 ) EXIT
In the state as shown in Fig. 1, operate the steering to bring
the arrow to EXIT and push the TEST button. The self-
testing will then end and return to the ADVERTISEMENT mode.
-22
CD TOP ASSY OUT RUN U/R USA (KR -00002) (D-2/2)
EM NO.
PART NO.
DESCRIPTION
1
KR- 10002
ASSY CABINET U/R USA
2
KR- 11001
ASSY CONT PANEL
3
KR-40002
ASSY PWR SPLY EXPORT
4
421-5800-45
ORIGINAL SEAL OUT RUN
5
420-5305-02
OWNERS MANUAL OUT RUN U/R ENG
6
421-6412-01
ADJ INSTR SH OUT RUN
8
KR— 0013
SHIELD BASE
10
421-6120
STICKER SEGA USA
11
117-5123
NAMEPLATE ELEC SPECIFICATION USA
12
81979
STICKER SERVICE INSTR
15
421-6119
STICKER FCC
16
82789
STICKER DANGER HIGH VOLTAGE
17
83602
STICKER SERIAL NO INFO
18
SGM-3640
POLYETHYLENE COVER HN UPRIGHT
19
SGM-2675
POLYETHYLENE BAG 240x370
20
SGB-1035X
KEY BAG
21
421-6186-1
DENOMINATION SHEET 1 GAME 2x25 1
22
421-6186-2
DENOMINATION SHEET 1 GAME 25 0
23
540-0009-01
WRENCH FOR TAMP SCR M8
24
540-0006-01
WRENCH FOR TAMP SCR M4
25
540-0007-01
WRENCH FOR TAMP SCR M5
26
540-0015-01
WRENCH FOR TAMP TYPE M6
27
220-5130
* VOL CONT B-5K OHM
28
834-6065-02
GAME BD OUT RUN
834-6065-04
GAME BD OUT RUN
29
422-0168
PLAY INSTR STICKER U/R
30
420-5318
DISPLAY MANUAL 20" 200-5090 ENG
201
029-0050
TMP PRF SCR BH M8x30
202
000-0530
M SCR PH M5X30
203
069-0001
FLT WSHER 5.5-20x1.6
204
000— 0412— FS
M SCR PH W/FS M4X12
205
046-0001
SCR NAIL THH 1.5x16
206
010-0310-F
S-TITE SCR PH W/F M3xl0
209
008-0516
TMP PRF SCR TH M5xl6
Note : VOL CONT refers to the potentiometer.
-24
(2) ASSY FL & SP UNIT EXPORT (KR-1070)
ITEM NO. PART NO. DESCRIPTION
1 KR-1067 FL & SP BASE
2 VE— 1036 FL BRKT
3 SGB— 3751— 5 WIRE HARN FL & SP UNIT
211-0087 CONN PLUG AMP 4P BROWN
211-0085 CONN PLUG AMP 2P BROWN
280-5015 FASTON RCPT 187
209-0023 CONN CLOSED END
101 390-5120-01 ASSY FL LIGHT 15W 60Hz PALUCK
102 211-0041 CONN PIN AMP
103 280-0419 HARNESS LUG
104 130-5001 SPEAKER 8 OHM 0120
201 005-3510 W SCR.RH 3.5x10
202 005— 3513— F W SCR RH W/F 3.5x13
203 010-0406— F S-TITE SCR PH W/F M4x6
- 25 -
(D ASSY SUB-CABINET U/R USA(KR-1600) (D-2/2)
ITEM NO.
PART NO.
DESCRIPTION
1
KR-1601
WODDEN CABINET
2
KR-1602
SUPPORT BRACKET
3
KR-1603
BACK DOOR
4
KR— 1604
FLOOR MAT
5
KR-1605
BRACKET HOLDER
7
SH-2061X
STOPPER
8
KR-1606
COVER CASHBOX
9
KR-1608
LOCK BRACKET
10
TI— 1079
LEG ADJUSTOR BRKT
11
601-0455
LEG ADJUSTOR
12
TA-1010
HINGE 148
13
220-5128-03
ASSY COIN CHUTE 2 DOOR USA 254x2
14
HN— 1050
SPACE RING
15
DP-1167
TNG LKG
16
DP-1148X
LKG TNG
17
117-0062
PLATE LOCK RETAINER
18
109-0045
KEY HOLDER
19
220-5044-01
MAG LOCK W/O KEY
20
220-5045-01
KEY MASTER FOR 220-5044-01
21
220-5046
MAG LOCK W/KEYS
22
SGB-3751-16
WIRE HARN COIN SW
211-0073
CONN PLUG AMP 4P WHITE
280-5016
FASTON RCPT 205
280-0425
CORD CLAMP 0 10
23
KR-1609
BRACKET UNDER RIGHT
24
KR-1610
BRACKET UNDER LEFT
101
211-0041
CONN PIN AMP
201
000— 0406— S
M SCR PH W/S M4x6
202
000-0408-S
M SCR PH W/S M4x8
204
000-0516— S
M SCR PH W/S M5xl6
205
005— 3516— F
W SCR RH W/F 3.5x16
206
000-0520— S
M SCR PH W/S M5X20
207
046-0001
SCR NAIL
208
059-0007
HEX NUT 3/8-16
209
000— 0306-S
M SCR PH W/S M3x6
210
244-063
DOUBLE FACE TAPE 20mm
-27
r Aj ASSY CABINET U/R USA (KR--10002) (D-2/3)
M NO.
PAR'] NO.
DESCRIPTION
i
KB -1000
ASSY SUB-CABINET U/R
UN - i 038
M ASK BOARD
HN- 1039 A
WINDOW GLASS
i
KK-1068
WINDOW MASK
V
AB LW
TV MASK 20
Ua
METER 11 UK"
7
KB BM?
CASHBOX
1 . R • 0:>
MA UNIT
i ■■
MO UUM*
( '.OVER
K.
HN .1042
LAN BKL
1 1
wn-1053 '
SiUARD PLATE
i.
-i*'; 1040
1 SOLDER MUM
I :
Ml M070
ASSY FL N SB UNIT EX PORI
■ 4
! 05 -C);B A
I'HK/S* MAIN SW
i .j
800-509! t
ASSY CLR DSPS; 20 TYPE 100V
Jw
.09 Ol),;,!
SW STOPPER 0 17
•N: 1064X
ERA ML 1 tOWER
IB
OR- 1065X
FRAME UPPER
oO-v,,}3;
DESIGN PLATE OUTRUN
>
Kit- 1071
ACCEL k BRAKE PEDAL
2 1
K ;■ - 12002
ASSY ACCEL & BRAKE U/R
2‘.
K K - 1073
SHAFT
‘-B
TV -1019
BRKT TV
2'J
8GB -3751- 1?
WIRE HARN EARTH
21.1 -016?
TERMINAL LUG ROUND ID 5
4 ■
SGB-375] -2
WIRE HARN FAN MOTOR
ill -0085
CONN PLUG AMI' 2P BROWN
‘ O
SGR-3751— 4
WIRE HARN EXT AC 100V
000-5133
CABLE & CONN 3001,
21 1-0085
CONN PLUG AMP 2P BROWN
211-0080
CONN CAP AMP 2P BROWN
211-0117
CONN CAP AMP 2P YELLOW
209-0032
CONN CLOSED END
27
AB 1151 Y
TV MASK GRAY SMOKE
28
SGB-3751— 6
WIRE HARN EXT FL
211-0085
CONN PLUG AMP 2P BROWN
211-0080
CONN CAP AMP 2P BROWN
29
SGB— 3751— 7
WIRE HARN EXT SI-
211-0087
CONN PLUG AMP 4P BROWN
211 0082
CONN CAP AMP 4P BROWN
30
SGB-3751— 9
WIRE HARN 50P
211-5105
CONN FEM 50P
211-0102
CONN PLUG AMP 4P YELLOW
211-0044
CONN CAP AMP 2P WHITE
211-0080
CONN CAP AMP 2P BROWN
211-0121
CONN CAP AMP 4P RED
211-0081
CONN CAP AMP 3P BROWN
211-0072
CONN CAP AMP 4P WHITE
211-0082
CONN CAP AMP 4P BROWN
212-5033
CONN FEM 2P
270-5016
FERRITE SLEEVE CORE
31
SGB-3751- 10
WIRE HARN 20P
211-5088
CONN FEM 20P
211-0060
CONN CAP AMP 3P WHITE
211-0046
CONN CAP AMP 6P WHITE
270-5016
FERRITE SLEEVE CORE
- 29 -
© ASSY CABINET U/R USA (KR- 10002) (D-3/3)
ITEM NO.
PART NO.
DESCRIPTION
32
SGB-3751-11
WIRE HARN RG8
211-0044
CONN CAP AMP 2P WHITE
211-0060
CONN CAP AMP 3P WHITE
212-5034
CONN FEM 6P
270-5016
FERRITE SLEEVE CORE
33
SGB-3751-15
WIRE HARN COIN METER
211-0087
CONN PLUG AMP 4P BROWN
209-0023
CONN CLOSED END
34
SGB-3751-2
WIRE HARN AC
211-0118
CONN CAP AMP 3P RED
209-0023
CONN CLOSED END
280-5015
FASTON RLPT 187
35
HN-1069
RUBBER CUSHION
36
80931
STICKER COIN METER
37
83005
STICKER MAIN SW PUSH ON PUSH OFF
38
SGB-3751— 18
WIRE HARN EXT DC
211-0096
CONN PLUG AMP 2P YELLOW
211-0115
CONN CAP AMP 2P RED
212-5034
CONN FEM 6P
39
839-0048
SSR BD DC MOTOR
40
KR-1612
BRACKET
101
220-5064
MAG CNTR 60 1G DC SV
102
260-0011
AXIAL FLOW FAN AC 100V 50~60Hz
103
280-0419
HARNESS LUG
104
211-0041
CONN PIN AMP
105
211-0042
CONN SOCKET AMP
106
211-0005
CONTACT
107
280-5008
CORD CLAMP 015
108
280-0425
CORD CLAMP 010
109
280-0418
BUSHING STRAIN RELIEF 8.3
110
280-0417
TERMINAL BINDING POST BLACK
111
600-0110
CA & PL ASSY
112
509-0039
SW PB TYPE
113
211-0005
CONN CLAMP LOCK
201
000— 0310-FS
M SCR PH W/FS M3X10
202
000— 0408— S
M SCR PH W/S M4x8
203
000-0416— FS
M SCR PH W/FS M4xl6
204
069-0001
FLT WSHR 5.5-20x1.6
205
000— 0520-S
M SCR PH W/S M5X20
206
031-0425— B
CRG BLT-BLK M4x25
207
000-0510-S
M SCR PH W/S M5xl0
208
065-0004
E RING 4mm
209
008-0425
TMP PRF SCR TH M4x25
210
010— 0408— F
S-TITE SCR PH W/F M4x8
211
051-0004
FLG NUT M4
212
008-0516
TMP PRF SCR TH M5xl6
213
008-0520
TMP PRF SCR TH M5x20
214
000-0530
M SCR PH M5X30
215
005— 3513— F
W SCR RH W/F 3.5x13
216
005-3510
W SCR PH 3.5X10
217
006-3110
W SCR FH 3.1x10
218
005-3520
W SCR PH 3.5x20
219
060-0006
FLT WSHR M6
220
008-0535
TMP PRF SCR TH M5x35
221
008-0416
TMP PRF SCR TH M4xl6
- 30 -
(5) ASSY CONTROL PANEL (KR-11001) (D-2/3)
ITEM NO.
PART NO.
DESCRIPTION
1
KR— 1133
CONTROL PANEL
2
KR— 1134
METER PANEL
3
KR-1132
CONT WOODEN BASE
4
KR-1105X
HANDLE BASE
5
KR-1106X
STEERING WHEEL SHAFT
6
KR-1107
SHAFT
7
KR— 1108
ARM PLATE
8
KR-1109X
ARM BAR
9
KR-1110Y
STEERING WHEEL STOPPER
10
KR-1111X
EXTENSION SPRING
11
KR— 1112
VOLUME BRACKET
12
KR-1113
BUMPER BRACKET
13 ■
KR-1114
BUMPER
14
KR— 1115
STOPPER
15
KR-1116
RUBBER STOPPER
16
KR-1117
PLATE
17
KR-1119
COLLAR B
18
KR— 1120
SPACER A
19
KR-1121X
STEERING HANDLE 0 270
20
KR-1122
KEY A
21
KR-1123
KEY B
22
KR-1125X
HANDLE EMBLEM
23
KR-1126
GEAR A
24
KR— 1127
GEAR B
25
KR— 1128
GEAR C
26
KR-1129
GEAR D
27
KR-1130
HINGE 590
28
KR-1131
BRACKET
29
KR-1118
COLLAR A
30
KR- 13001
ASSY SHIFT LEVER S
31
KR— 1141
BRACKET A
32
KR— 1142
BRACKET B
33
117-5133
START PLATE
34
KR— 1143
BASE
35
KR— 1144
SLIDE BASE
36
KR— 1145
ROLLER BRACKET
37
KR-1146
MOTOR BRACKET
38
KR— 1147
ROD
39
KR— 1148
CAM
40
KR-1149
SHOULDER SCREW
41
KR— 1150
SHAFT
42
KR— 1151
SHAFT LONG
43
KR— 1152
SHAFT SHORT
44
KR-1153
SLIDE PLATE
45
KR— 1154
ROLLER A
46
KR-1155
PLASTIC WASHER
47
KR— 1156
COLLAR
48
KR— 1157
SPACER
49
KR— 1165
SPACER
50
KR-1137
STOPPER WASHER
51
KR-1164
ROLLER B
52
KR— 1171
PLATE
53
KR-1173
COVER PLATE
54
KR— 1174
SPACER
- 32 -
(D ASSY CONTROL PANEL (KR — 11001 ) (D-3/3)
ITEM NO.
PART NO.
DESCRIPTION
SGB-3751-13
WIRE HARN HANDLE VR
211-0059
CONN PLUG AMP 3P WHITE
SGB-3751-14
WIRE HARN START SW
211-0100
CONN PLUG AMP 4P RED
280-0472
FASTON RCPT 110
SGB— 3751— 19
WIRE HARN DC MOTOR
211-0094
CONN PLUG AMP 2P
209-0023
CONN CLOSED END
101
100-5015
BEARING 10
102
100-5035
BEARING 0 20
103
220-5130
VOL CONT B-5K OHM
104 "
509-5053
PUSH BTN SWITCH GREEN W/LAMP
105
211-0041
CONN PIN AMP
106
350-5086
MOTOR DC 45V
107
280-5008
CORD CLAMP 0 15
108
280-0419
HARNESS LUG
109
601-0460
TIE BELT
201
030-0825
HEX BLT M8x25
202
060-0008
FLT WSHR M8
203
061-0008
SPR WSHR M8
204
054-0005
U NUT M5
205
050-0010
HEX NUT M10
206
069-0009
FLT WSHR 10.5-28x2
207
061-0010
SPR WSHR M10
208
060-0010
FLT WSHR M10
209
060-0005
FLT WSHR M5
211
008-0512
TMP PRF SCR TH M5xl2
212
000-0408-FS
M SCR PH WFS M4x8
213
000-0510— FS
M SCR PII W/FS M5xl0
214
028-0010
SET SCR HEX SKT CP M5x8
215
028-0014
SET SCR HEX SKT CP UNBR M4x4
216
029-0078
TMP PRF SCR TH M6xl6
217
061-0006
SPR WSHR M6
218
000— 0510— S
M SCR PH W/S M5X10
219
069-0022
FLT WSHR 5.5-14x1
220
028-0007
SET SCR HEX SKT CP UNBR M4xl0
221
000-0416-FS
M SCR PH M4xl6 W/FS
222
008-0516
TMP PRF SCR TH M5xl6
223
008-0416
TMP PRF SCR TH M4xl6
224
008-0408
TMP PRF SCR TH M4x8
225
001-0420
M SCR FHT M4x20
227
000— 0514— S
M SCR PH 5x14 W/S
228
001-0516
M SCR FH 5X16
229
005-3516
W SCR RH 3.5X16
231
054-0006
U NUT M6
232
045-0003
COT PIN 1.6x12
233
045-0005
COT PIN 2x15
234
028-0012
SET SCR CHEESE HEAD SPECIAL M5xl2
235
054-0004
U NUT M4
236
008-0425
TMP PRF SCR TH M4x25
237
045-0014
SPR PIN UNBR 3x26
238
005-3113
W SCR RH 3.1x13
239
006-3113
W SCR FH 3.1x13
- 33 -
(D ASSY ACCEL & BRAKE U/R (KR - 1 2002) (D-2/2)
ITEM NO.
PART NO.
DESCRIPTION
1
KR-1216
LID
2
KR-1217
PEDAL BRACKET
3
KR— 1218
STOPPER BRACKET
4
KR-1219
ACCEL BAR
5
KR-1220
BRAKE BAR AND PEDAL
6
KR— 1221
BUMPER BRACKET A
7
KR-1222X
BUMPER BRACKET B
8
KR— 1223
BUMPER A
9
KR— 1224
BUMPER B
10
KR-1225
SPRING STOPPER
11
KR— 1205
VR BRACKET
12
KR-1208
SHAFT BRAKE ACCEL
13
KR-1209
COLLAR
14
KR-1210
TORSION SPRING A
15
KR-1211
TORSION SPRING B
16
KR— 1213
BUMPER
18
SGB-3751-12
211-0045
WIRE HARN ACCEL & BRAKE VR
CONN PLUG AMP 6P WHITE
101
220-5130
VOL CONT B-5K OHM
102
601-5410
GEAR 15 06
103
601-5423
GEAR 1/6
104
211-0041
CONN PIN AMP
105
280-5008
CORD CLAMP 015
106
601-0460
TIE BELT
201
000-0406-S
M SCR PH W/S M4x6
202
000-0408-S
M SCR PH W/S M4x8
203
000— 0408-FS
M SCR PH W/FS M4x8
204
000— 0510-FS
M SCR PH W/FS M5X10
205 '
028-0002
SET SCR PH SPCL iM3x6
206
031— 0514— B
CRG BLT BLK M5xl4
207
050-0008
HEX NUT M8
208
051-0005
FLG NUT M5
209
060-0008
FLT WSHR M8
210
061-0008
SPR WSHR M8
- 35 -
Q) ASSY SHIFT LEVER S
EM No.
PART No.
1
KR— 1312
2
KR-1314
3
KR-1303
4
KR-1320
5
KR-1304
6
KR-1315
7
SGB-3740— 5
211-0043
280-5015
8
KR— 1316
9
KR-1318
101
211-0041
102
101-5004
103
509-5088
104
310-0012
105
117-0141
201
069-0005
202
000- 0408- FS
203
069-0049
204
000-0316
205
069-0007
206
065-0006
207
054-0004
208
010— 0408-F
(KR-13001) ( D— 2/2)
DESCRIPTION
SHIFT BRACKET B
COVER BRACKET B
STOPPER
COMPRESSION SPRING
SHAFT
SUB ASSY SHIFT LEVER
WIRE IIARN SHIFT SW
CONN PLUG AMP 2P WHITE
FASTON RCPT 187
SPACER
MOUNT BRACKET
CONN PIN AMP
STEEL BALL 08.7312
SW MICRO TYPE
PAPER INSULATOR
LOCK PLATE
FLT WHIR SPECIAL 8.3-14.3x0.5
M SCR PH W/FS M4x8
NYLON WASHER SPECIAL 8.5-14x1
M SCR PII M3xl6
FLT WSHR
E RING 6mm
M4 U NUT
S-TITE SCR W/F M4x8
- 37 -
® ASSY PWR SPLY EXPORT (KR-40002) (D-i/2)
ITEM
1
2
3
4
5
6
7
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
201
202
203
204
PART NO.
DESCRIPTION
KR— 4002
BASE
839-0035
PWR AMP DC 12V 10W
560-5095
PWR XFMP 90— 240V 100V 11V 35V
421-6503
STICKER FUSE INSTR
421-6504
STICKER FUSE INSTR
81319
STICKER 120V
80666
STICKER 200V
80556
STICKER 220V
80595
STICKER 230V
80309
STICKER 240V
RA-4002
COVER
SGB-3751-1
WIRE HARN PWR SPLY
211-0085
CONN PLUG AMP 2P BROWN
211-0097
CONN PLUG AMP 3P RED
211-0080
CONN CAP AMP 2P BROWN
211-0060
CONN CAP AMP 3P WHITE
211-0082
CONN CAP AMP 4P BROWN
211-0123
CONN CAP AMP 4P YELLOW
212-5076
CONN FEM 4P
212-5034
CONN FEM 6P
212-5067
CONN FEM 8P
211-5101
CONN FEM 10P
211-0117
CONN CAP AMP 2P YELLOW
270-5016
FERRITE SLEEVE CORE
211-0116
CONN CAP AMP 2P ORANGE
117-0184
TERMINAL PLATE IL 4P
117-5131
TERMINAL PLATE 5P
150-0173
CAP E 4700 MF 50V C-TYPE
400-5055
SW REGU 90- 240V 5V 10 A
481-0157
DIODE BRIDGE S5VB20
514-0064
FU HLDR 2P W/COVER
514-0065
FU HLDR IP W/COVER
514-0036
FU 3A 6.4x30mm
514-0034
FU 5A 6.4x30mm
514-0040
FU 4A 6.5x30mm
514-0031
FU 6A 6.5x30mm
601-0429
NOISE FLTR AC 250V 4A
601-0769
STAPLE MAX #3
280-0419
HARNESS LUG
211-0167
TERMINAL LUG ROUND ID 5
211-0041
CONN PIN AMP
211-0042
CONN SOCKET AMP
211-0005
CONN CLAMP LOCK
211-5047
CONTACT
280-5015
FASTON RCPT 187
280-0472
FASTON RCPT 110
150-0265
CAP E 22000 MF 25V C-TYPE
000-0414-FS
M SCR PH W/FS M4X14
005-3110
W SCR RH 3.1X10
005-31 13-F
W SCR RH W/F 3.1x13
005-3120
W SCR RH 3.1X20
- 39 -
SEGA ENTERPRISES, LTD.
No. 2-12, Haneda 1-chome
Ohta-ku, Tokyo 144, Japan
o Tel. : (03) 743 - 7438
o FAX : (03) 743 - 5539
o TLX : J22357 SEGASTAR
© SEGA 1986
Printed in Japan